Upon hitting line number line, the compiler finds: #include "bar" or.

The main licensing options available are GPL V2 or Commercial:/// This is the appropriate option if you want to share the source code of your/// application with everyone you distribute it to, and you also want to give them/// the right to share who uses it. I had the same problem. Name vw_tx_active() changed from incorrect/// \version 1.20 Added support for ATtiny84, patched by Chuck Benedict./// \version 1.21 Added support for most AVR8 platforms with proper configuration, without depending/// on Arduino environment, such as Atmega32u2, Atmega32U4, At90USB162 etc, /// contributed by Alexandru Daniel Mircescu.

Added vw_get_rx_good() and vw_get_rx_bad()/// \version 1.18 Added support for Maple, Flymaple etc with STM32F103RE processor using timer 1./// Tested with Flymaple 1.1 and maple-ide-v0.0.12/// \version 1.19 Added new function vw_rx_inverted(), to allow the incoming RX to be inverted (normally high)./// Minor improvements to timer setup for Maple. Your compiler just tried to compile the file named foo.cc.

Defaults to 12. name="submit" src="https://www.paypalobjects.com/en_AU/i/btn/btn_donateCC_LG.gif" /> \endhtmlonly/// VirtualWire is a trademark of AirSpayce Pty Ltd.


Messages are sent with a training preamble,/// message length and checksum. /// Arduino environment, courtesy r4z0r7o3. /// Runs on a wide range of Arduino processors using Arduino IDE 1.0 or later./// with MSP430G2553 / G2452 and Arduino with ATMega328 (courtesy Yannick DEVOS - XV4Y), /// but untested by us. Ask Question Asked 7 years, 6 months ago. I see that I didn’t have it in my library (closest thing was Keyboard) so I went to the library manager and downloaded it. asm/errno.h: No such file or directory. Then launch the Arduino environment; you/// should see the library in the Sketch->Import Library menu, and example/// This library is offered under a free GPL license for those who want to use it that way. If you didn't put the files there then they won't be found. This is the output of the build process: bug. 6.
3 comments Labels. Ramp wraps modulo this number// Standard is if a transition occurs before VW_RAMP_TRANSITION (80) in the ramp,// the ramp is retarded by adding VW_RAMP_INC_RETARD (11)// If there is no transition it is adjusted by VW_RAMP_INC (20)#define VW_RAMP_INC (VW_RX_RAMP_LEN/VW_RX_SAMPLES_PER_BIT)#define VW_RAMP_INC_RETARD (VW_RAMP_INC-VW_RAMP_ADJUST)#define VW_RAMP_INC_ADVANCE (VW_RAMP_INC+VW_RAMP_ADJUST)/// 36 alternating 1/0 bits, followed by 12 bits of start symbol/// Followed immediately by the 4-6 bit encoded byte count, /// Each byte from the byte count on is translated into 2x6-bit words/// Caution, each symbol is transmitted LSBit first, // Cant really do this as a real C++ class, since we need to have // Set the digital IO pin which will be used to enable the transmitter (press to talk, PTT)' /// \param[in] pin The Arduino pin number to enable the transmitter. It also runs on Teensy 3.0 and 3.1 (courtesy of Paul/// Stoffregen) using the Arduino IDE 1.0.5 and the Teensyduino addon 1.18.

I've installed wxwidgets. Use is subject to license/// conditions. The VirtualWire/// library, when built for ATTiny85, takes over timer 0, which prevents use/// of millis() etc but does permit analog outputs./// To install, unzip the library into the libraries sub-directory of your/// Arduino application directory. /// Initialise the VirtualWire software, to operate at speed bits per second /// Call this one in your setup() after any vw_set_* calls /// Must call vw_rx_start() before you will get any messages /// \param[in] speed Desired speed in bits per second /// Start the Phase Locked Loop listening to the receiver /// Must do this before you can receive any messages /// When a message is available (good checksum or not), vw_have_message(); /// Stop the Phase Locked Loop listening to the receiver /// No messages will be received until vw_rx_start() is called again /// \return true if the transmitter is active else false /// Block until a message is available or for a max time /// \param[in] milliseconds Maximum time to wait in milliseconds. /// \return true if a message is available, false if the wait timed out. Support for arduino IDE prior to 1.0 is now abandoned./// \version 1.27 Reinstated VWutil/crc16.h for the benefit of other platforms such as Teensy./// Testing on Teensy 3.1.

/// \param[in,out] len Available space in buf.

Active 1 month ago. /// By default the RX pin is expected to be low when idle, and to pulse high /// This flag forces it to be inverted.

Uploading code to the Arduino also works and gives the expected results.Hi, I think you have the current stable version, which has a bug... Could you try to use Arduino-CMake from here (the develop branch) Actually, I have just merged in the latest changes from the develop branch into master, so just re-update your checkout of Arduino-CMake.Successfully merging a pull request may close this issue. The ones listed below are available in common retail/// outlets in Australia and other countries for under $10 per unit. gcc.exe: error: CreateProcess: No such file or directory.

5 ... 86 /// library using 'VirtualWire_Config.h' header file for describing the access. Moved CHANGES log to this version history./// Ensure vw_rx_pin is not accessed unless receiver is enabled/// \version 1.12 Compiles and runs on on Energia with MSP430G2553 / G2452 and Arduino with ATMega328.